WCSAR-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object WCSAR-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*
1789974276	13.5 Volt	0 Pkt	0 Pkt
1789950855	13.5 Volt	0 Pkt	0 Pkt
1789949053	13.5 Volt	0 Pkt	0 Pkt
1789925630	13.58 Volt	0 Pkt	0 Pkt
1789923828	13.58 Volt	0 Pkt	0 Pkt
1789913919	13.5 Volt	0 Pkt	0 Pkt
1789894100	13.5 Volt	10 Pkt	10 Pkt
1789891397	13.5 Volt	0 Pkt	0 Pkt
1789852655	13.58 Volt	0 Pkt	0 Pkt
1789852653	13.58 Volt	0 Pkt	0 Pkt
1789841903	13.58 Volt	0 Pkt	0 Pkt
1789841303	13.58 Volt	0 Pkt	0 Pkt
1789840098	13.58 Volt	0 Pkt	0 Pkt
1789833742	13.58 Volt	10 Pkt	10 Pkt
1789813952	13.5 Volt	10 Pkt	10 Pkt
1789785998	13.43 Volt	0 Pkt	0 Pkt
1789783293	13.43 Volt	0 Pkt	0 Pkt
1789660776	13.58 Volt	10 Pkt	10 Pkt
1789640956	13.58 Volt	10 Pkt	10 Pkt
1789632849	13.58 Volt	10 Pkt	10 Pkt
1789631948	13.58 Volt	10 Pkt	10 Pkt
1789629245	13.58 Volt	10 Pkt	10 Pkt
1789628344	13.58 Volt	10 Pkt	10 Pkt
1789627443	13.58 Volt	10 Pkt	10 Pkt
1789624741	13.58 Volt	10 Pkt	10 Pkt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Temp: 0, 0.5, -64

I1: 0, 19.5, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)