VK2CPR-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2CPR-5. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TX*	V_Bat*	V_Ext*
1778222199	26 Count	4.19 VDC	0.14 VDC
1778220396	25 Count	4.21 VDC	0.14 VDC
1778218613	24 Count	4.18 VDC	0.14 VDC
1778218613	23 Count	4.16 VDC	0.14 VDC
1778217767	22 Count	4.23 VDC	0.14 VDC
1778215965	21 Count	4.23 VDC	0.14 VDC
1778214162	20 Count	4.2 VDC	0.14 VDC
1778212359	19 Count	4.23 VDC	0.14 VDC
1778212317	18 Count	4.18 VDC	0.14 VDC
1778212070	17 Count	4.21 VDC	0.14 VDC
1778212024	16 Count	4.2 VDC	0.14 VDC
1778211441	15 Count	4.2 VDC	0.14 VDC
1778211027	14 Count	4.22 VDC	0.14 VDC
1778209224	13 Count	4.18 VDC	0.14 VDC
1778207421	12 Count	4.25 VDC	0.14 VDC
1778205619	11 Count	4.18 VDC	0.14 VDC
1778205565	10 Count	4.23 VDC	0.14 VDC
1778205548	9 Count	4.19 VDC	0.14 VDC
1778202942	8 Count	4.2 VDC	0.14 VDC
1778202875	7 Count	0 VDC	0 VDC
1778202104	6 Count	0 VDC	0 VDC
1778202097	5 Count	0 VDC	0 VDC
1778202073	4 Count	0 VDC	0 VDC
1778200457	3 Count	4.21 VDC	0.14 VDC
1778200287	2 Count	4.21 VDC	0.14 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)