F5ZYP-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F5ZYP-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1772611609	14.03 Volt	200 Pkt	110 Pkt	93 Pcnt
1772611310	14.03 Volt	190 Pkt	100 Pkt	92 Pcnt
1772611309	14.03 Volt	190 Pkt	100 Pkt	92 Pcnt
1772611009	14.03 Volt	190 Pkt	110 Pkt	91 Pcnt
1772610709	14.03 Volt	190 Pkt	100 Pkt	89 Pcnt
1772610409	14.03 Volt	190 Pkt	110 Pkt	88 Pcnt
1772610110	14.03 Volt	210 Pkt	110 Pkt	88 Pcnt
1772610109	14.03 Volt	210 Pkt	110 Pkt	88 Pcnt
1772609831	14.03 Volt	200 Pkt	110 Pkt	87 Pcnt
1772609509	14.03 Volt	200 Pkt	100 Pkt	86 Pcnt
1772609209	14.03 Volt	200 Pkt	100 Pkt	85 Pcnt
1772608909	14.03 Volt	190 Pkt	90 Pkt	84 Pcnt
1772608609	14.03 Volt	190 Pkt	90 Pkt	85 Pcnt
1772608310	14.03 Volt	180 Pkt	90 Pkt	87 Pcnt
1772608309	14.03 Volt	180 Pkt	90 Pkt	87 Pcnt
1772608009	14.03 Volt	180 Pkt	90 Pkt	86 Pcnt
1772607710	14.03 Volt	170 Pkt	80 Pkt	87 Pcnt
1772607709	14.03 Volt	170 Pkt	80 Pkt	87 Pcnt
1772607409	14.03 Volt	160 Pkt	70 Pkt	87 Pcnt
1772607110	14.03 Volt	150 Pkt	70 Pkt	89 Pcnt
1772607109	14.03 Volt	150 Pkt	70 Pkt	89 Pcnt
1772606809	14.03 Volt	130 Pkt	60 Pkt	88 Pcnt
1772606509	14.03 Volt	110 Pkt	50 Pkt	89 Pcnt
1772606209	13.95 Volt	110 Pkt	50 Pkt	88 Pcnt
1772605910	14.03 Volt	100 Pkt	40 Pkt	91 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)