WC4PEM Telemetry

This is the latest recevied telemetry packets stored in our database for station/object WC4PEM. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Vin*	Rx1h*	Eff1h*
1765495011	29.5 C	13.8 Volt	890 Pkt	68 Pcnt
1765495011	29.5 C	13.8 Volt	890 Pkt	68 Pcnt
1765494411	29.5 C	13.8 Volt	870 Pkt	68 Pcnt
1765494411	29.5 C	13.8 Volt	870 Pkt	68 Pcnt
1765493811	29 C	13.8 Volt	880 Pkt	70 Pcnt
1765493211	28.5 C	13.8 Volt	820 Pkt	71 Pcnt
1765493211	28.5 C	13.8 Volt	820 Pkt	71 Pcnt
1765492611	29 C	13.8 Volt	840 Pkt	71 Pcnt
1765492611	29 C	13.8 Volt	840 Pkt	71 Pcnt
1765492011	28.5 C	13.8 Volt	850 Pkt	72 Pcnt
1765492011	28.5 C	13.8 Volt	850 Pkt	72 Pcnt
1765491411	29 C	13.8 Volt	860 Pkt	72 Pcnt
1765491411	29 C	13.8 Volt	860 Pkt	72 Pcnt
1765490811	28.5 C	13.8 Volt	890 Pkt	72 Pcnt
1765490811	28.5 C	13.8 Volt	890 Pkt	72 Pcnt
1765490211	29 C	13.8 Volt	870 Pkt	70 Pcnt
1765490211	29 C	13.8 Volt	870 Pkt	70 Pcnt
1765489611	29 C	13.8 Volt	890 Pkt	72 Pcnt
1765489611	29 C	13.8 Volt	890 Pkt	72 Pcnt
1765489011	28.5 C	13.8 Volt	870 Pkt	72 Pcnt
1765488412	29 C	13.8 Volt	840 Pkt	72 Pcnt
1765488411	29 C	13.8 Volt	840 Pkt	72 Pcnt
1765487811	28.5 C	13.8 Volt	850 Pkt	72 Pcnt
1765487211	29 C	13.8 Volt	840 Pkt	73 Pcnt
1765486612	29 C	13.8 Volt	870 Pkt	75 Pcnt

*Used Equation Coefficients:

Temp: 0, 0.5, -64

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)