N6ZKI-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N6ZKI-4. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Battery*	Temp*
1781565178	13.42 Volts	111.68 Deg.F
1781564697	13.42 Volts	115.2 Deg.F
1781564457	13.54 Volts	116.95 Deg.F
1781558828	13.62 Volts	102.89 Deg.F
1781558588	13.65 Volts	104.65 Deg.F
1781558348	13.62 Volts	103.77 Deg.F
1781555348	13.74 Volts	109.04 Deg.F
1781554627	13.74 Volts	109.04 Deg.F
1781551112	13.74 Volts	108.16 Deg.F
1781550872	13.74 Volts	109.92 Deg.F
1781550632	13.71 Volts	109.04 Deg.F
1781550391	13.77 Volts	104.65 Deg.F
1781480757	12.16 Volts	121.35 Deg.F
1781480516	14.01 Volts	119.59 Deg.F
1781310624	13.62 Volts	116.08 Deg.F
1781146801	13.62 Volts	86.19 Deg.F
1781146560	13.54 Volts	87.07 Deg.F
1781146320	13.54 Volts	89.71 Deg.F
1781145840	13.65 Volts	94.1 Deg.F
1781145599	13.6 Volts	96.74 Deg.F
1781145359	13.65 Volts	100.25 Deg.F
1781145120	13.54 Volts	103.77 Deg.F
1781144880	13.62 Volts	105.53 Deg.F
1781135588	13.65 Volts	80.04 Deg.F
1781135349	13.65 Volts	80.92 Deg.F

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.879, -459.67

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)