SR8WXD Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR8WXD. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Digi10min*	Vbatt*
1765638839	42 Pkt	7 Pkt	1 Pkt	13.3 V
1765638068	68 Pkt	8 Pkt	2 Pkt	13.32 V
1765637298	67 Pkt	7 Pkt	1 Pkt	13.3 V
1765636528	70 Pkt	8 Pkt	3 Pkt	13.28 V
1765635758	69 Pkt	7 Pkt	2 Pkt	13.32 V
1765634987	65 Pkt	6 Pkt	0 Pkt	13.3 V
1765634214	58 Pkt	8 Pkt	2 Pkt	13.34 V
1765632664	50 Pkt	7 Pkt	1 Pkt	13.28 V
1765631893	49 Pkt	6 Pkt	0 Pkt	13.34 V
1765631126	64 Pkt	6 Pkt	1 Pkt	13.3 V
1765630357	52 Pkt	6 Pkt	1 Pkt	13.3 V
1765628050	57 Pkt	8 Pkt	2 Pkt	13.32 V
1765627282	39 Pkt	7 Pkt	1 Pkt	13.32 V
1765626515	37 Pkt	6 Pkt	0 Pkt	13.32 V
1765625747	27 Pkt	6 Pkt	0 Pkt	13.28 V
1765624977	44 Pkt	5 Pkt	1 Pkt	13.36 V
1765623442	48 Pkt	6 Pkt	1 Pkt	13.32 V
1765622673	49 Pkt	8 Pkt	2 Pkt	13.3 V
1765621902	63 Pkt	8 Pkt	2 Pkt	13.32 V
1765621133	72 Pkt	8 Pkt	2 Pkt	13.32 V
1765620361	63 Pkt	8 Pkt	2 Pkt	13.3 V
1765619590	77 Pkt	6 Pkt	2 Pkt	13.3 V
1765618824	87 Pkt	7 Pkt	2 Pkt	13.32 V
1765618054	107 Pkt	7 Pkt	2 Pkt	13.32 V
1765616515	138 Pkt	6 Pkt	0 Pkt	13.32 V

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)