DG0MG-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DG0MG-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Ubat*	TxPwr*
1788584698	22 degC	3.38 V	20 dBm
1788584091	22 degC	3.38 V	20 dBm
1788583790	22 degC	3.38 V	17 dBm
1788583488	22 degC	3.38 V	20 dBm
1788583186	22 degC	3.38 V	18 dBm
1788582885	22 degC	3.38 V	20 dBm
1788581678	22 degC	3.38 V	20 dBm
1788579863	22 degC	3.38 V	20 dBm
1788577750	22.2 degC	3.38 V	15 dBm
1788577146	22.2 degC	3.38 V	16 dBm
1788576543	22.2 degC	3.38 V	17 dBm
1788575638	22.2 degC	3.38 V	20 dBm
1788575336	22.2 degC	3.38 V	19 dBm
1788575034	22.2 degC	3.38 V	20 dBm
1788573827	22.2 degC	3.38 V	20 dBm
1788572014	22.2 degC	3.38 V	20 dBm
1788570807	22.5 degC	3.38 V	20 dBm
1788569601	22.5 degC	3.38 V	20 dBm
1788569297	22.5 degC	3.38 V	17 dBm
1788568693	22.5 degC	3.38 V	18 dBm
1788568090	22.5 degC	3.38 V	19 dBm
1788567788	22.5 degC	3.38 V	20 dBm
1788567185	22.5 degC	3.38 V	20 dBm
1788565975	22.5 degC	3.38 V	20 dBm
1788563561	22.5 degC	3.38 V	20 dBm

*Used Equation Coefficients:

Temp: 0, 0.1, -273

Ubat: 0, 0.001, 0

TxPwr: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)