SR9POD Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9POD. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	T_in*	Rx1h*	Dg1h*
1789965606	13.65 Volt	21 C	190 Pkt	10 Pkt
1789965008	13.65 Volt	21 C	160 Pkt	20 Pkt
1789964406	13.65 Volt	21 C	140 Pkt	10 Pkt
1789963806	13.65 Volt	21 C	110 Pkt	10 Pkt
1789963209	13.65 Volt	21 C	100 Pkt	0 Pkt
1789962606	13.65 Volt	21.5 C	90 Pkt	0 Pkt
1789962006	13.65 Volt	21.5 C	90 Pkt	0 Pkt
1789961406	13.65 Volt	21.5 C	100 Pkt	0 Pkt
1789960806	13.65 Volt	21.5 C	100 Pkt	0 Pkt
1789960206	13.65 Volt	21.5 C	100 Pkt	0 Pkt
1789959606	13.65 Volt	21.5 C	120 Pkt	0 Pkt
1789959006	13.65 Volt	21.5 C	120 Pkt	0 Pkt
1789958406	13.65 Volt	21.5 C	110 Pkt	0 Pkt
1789957806	13.65 Volt	21.5 C	100 Pkt	0 Pkt
1789957206	13.65 Volt	22 C	90 Pkt	0 Pkt
1789956606	13.65 Volt	22 C	80 Pkt	10 Pkt
1789956013	13.65 Volt	22 C	70 Pkt	10 Pkt
1789955407	13.65 Volt	22 C	70 Pkt	10 Pkt
1789954806	13.65 Volt	22 C	70 Pkt	10 Pkt
1789954206	13.65 Volt	22.5 C	70 Pkt	10 Pkt
1789953606	13.65 Volt	22.5 C	70 Pkt	10 Pkt
1789953006	13.65 Volt	22.5 C	70 Pkt	10 Pkt
1789952410	13.65 Volt	22.5 C	60 Pkt	10 Pkt
1789951806	13.65 Volt	22.5 C	60 Pkt	10 Pkt
1789951245	13.65 Volt	22.5 C	70 Pkt	10 Pkt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

T_in: 0, 0.5, -64

T_out: 0, 1, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)