ED7ZAC-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED7ZAC-4. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Dg1h*	Eff1h*	Temp*
1780524341	-64 Pkt	100 Pcnt	26.5 Grad
1780524041	-64 Pkt	100 Pcnt	26.5 Grad
1780523741	-64 Pkt	100 Pcnt	26.5 Grad
1780523441	-64 Pkt	100 Pcnt	26.5 Grad
1780523141	-64 Pkt	100 Pcnt	26.5 Grad
1780522841	-64 Pkt	100 Pcnt	26.5 Grad
1780522541	-64 Pkt	100 Pcnt	26.5 Grad
1780522241	-64 Pkt	100 Pcnt	26.5 Grad
1780521941	-64 Pkt	100 Pcnt	26.5 Grad
1780521641	-64 Pkt	100 Pcnt	26.5 Grad
1780521341	-64 Pkt	100 Pcnt	26.5 Grad
1780521041	-64 Pkt	100 Pcnt	26.5 Grad
1780520741	-64 Pkt	100 Pcnt	26.5 Grad
1780520441	-64 Pkt	100 Pcnt	26.5 Grad
1780520141	-64 Pkt	100 Pcnt	26.5 Grad
1780519841	-64 Pkt	100 Pcnt	26.5 Grad
1780519541	-64 Pkt	100 Pcnt	27 Grad
1780519241	-64 Pkt	100 Pcnt	27 Grad
1780518941	-64 Pkt	100 Pcnt	27 Grad
1780518641	-64 Pkt	100 Pcnt	27 Grad
1780518341	-64 Pkt	100 Pcnt	27 Grad
1780518041	-64 Pkt	100 Pcnt	27 Grad
1780517741	-64 Pkt	100 Pcnt	27 Grad
1780517441	-64 Pkt	100 Pcnt	27 Grad
1780517141	-64 Pkt	100 Pcnt	27 Grad

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Dg1h: 0, 0.5, -64

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)