SP6ICO-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP6ICO-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	V_Bat*	V_Ext*
1753617580	546 Count	4.25 VDC	0.14 VDC
1753617260	545 Count	4.16 VDC	0.14 VDC
1753607586	544 Count	4.23 VDC	0.14 VDC
1753605782	543 Count	4.22 VDC	0.14 VDC
1753603980	542 Count	4.18 VDC	0.14 VDC
1753602177	541 Count	4.26 VDC	0.14 VDC
1753600374	540 Count	4.24 VDC	0.14 VDC
1753598571	539 Count	4.3 VDC	0.14 VDC
1753596768	538 Count	4.17 VDC	0.14 VDC
1753594965	537 Count	4.24 VDC	0.14 VDC
1753593163	536 Count	4.26 VDC	0.14 VDC
1753591360	535 Count	4.14 VDC	0.14 VDC
1753534848	534 Count	4.17 VDC	0.14 VDC
1753524402	532 Count	4.27 VDC	0.14 VDC
1753522582	531 Count	4.23 VDC	0.14 VDC
1753520779	530 Count	4.21 VDC	0.14 VDC
1753518975	529 Count	4.29 VDC	0.14 VDC
1753517173	528 Count	4.25 VDC	0.14 VDC
1753515370	527 Count	4.18 VDC	0.14 VDC
1753513567	526 Count	4.28 VDC	0.14 VDC
1753463340	524 Count	4.25 VDC	0.14 VDC
1753452601	523 Count	4.23 VDC	0.14 VDC
1753447227	520 Count	4.27 VDC	0.14 VDC
1753445423	519 Count	4.16 VDC	0.14 VDC
1753443621	518 Count	4.25 VDC	0.14 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)