SR9WXJ Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9WXJ. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Rx10min*	Digi10min*	Vbatt*
1785274589	20 Pkt	0 Pkt	13.04 V
1785273860	20 Pkt	0 Pkt	13.1 V
1785273128	20 Pkt	0 Pkt	13.06 V
1785272399	19 Pkt	1 Pkt	13.1 V
1785271680	20 Pkt	0 Pkt	13.12 V
1785270950	20 Pkt	0 Pkt	13.1 V
1785270218	20 Pkt	0 Pkt	13.06 V
1785269490	20 Pkt	0 Pkt	13.1 V
1785268758	20 Pkt	0 Pkt	13.08 V
1785268027	20 Pkt	0 Pkt	13.12 V
1785267295	20 Pkt	0 Pkt	13.14 V
1785266564	20 Pkt	0 Pkt	13.14 V
1785265834	19 Pkt	0 Pkt	13.16 V
1785265115	20 Pkt	0 Pkt	13.16 V
1785264383	20 Pkt	0 Pkt	13.12 V
1785263652	20 Pkt	0 Pkt	13.16 V
1785262922	20 Pkt	0 Pkt	13.38 V
1785262191	20 Pkt	0 Pkt	13.78 V
1785261458	20 Pkt	0 Pkt	14.04 V
1785260725	20 Pkt	0 Pkt	14.16 V
1785259994	20 Pkt	0 Pkt	14.18 V
1785259262	20 Pkt	0 Pkt	14.2 V
1785258529	69 Pkt	0 Pkt	14.22 V

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Visc10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)