BM6HML-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM6HML-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1780562049	37.3 C	4 p	10 p	149 p
1780560848	37.8 C	3 p	9 p	147 p
1780559649	36.1 C	3 p	8 p	146 p
1780558449	35.6 C	3 p	7 p	145 p
1780557249	36.1 C	2 p	6 p	144 p
1780554849	37.9 C	2 p	7 p	144 p
1780553648	34.3 C	2 p	7 p	144 p
1780552449	37.5 C	3 p	8 p	144 p
1780551249	36.4 C	2 p	8 p	143 p
1780550048	36.8 C	3 p	8 p	143 p
1780548849	37 C	3 p	7 p	142 p
1780547649	35.1 C	2 p	6 p	141 p
1780546449	35.4 C	2 p	7 p	141 p
1780545248	35.5 C	2 p	7 p	141 p
1780544048	35.7 C	3 p	7 p	141 p
1780542849	37.4 C	2 p	6 p	140 p
1780541649	37.7 C	2 p	6 p	140 p
1780540449	36.9 C	2 p	6 p	140 p
1780539248	35.6 C	2 p	6 p	140 p
1780538049	37.7 C	2 p	6 p	140 p
1780536849	37.4 C	2 p	6 p	140 p
1780535649	34.3 C	2 p	7 p	140 p
1780534448	36.3 C	2 p	7 p	140 p
1780533249	35 C	3 p	7 p	140 p
1780532049	37 C	2 p	6 p	139 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)