OE6ACM-14 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE6ACM-14. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Pres*	Humi*
1790020575	11.5 deg.C	935 mbar	45 Percen
1790020275	11.5 deg.C	935 mbar	45 Percen
1790019975	11.5 deg.C	936 mbar	46 Percen
1790019675	11.5 deg.C	935 mbar	45 Percen
1790019375	11.5 deg.C	935 mbar	45 Percen
1790019075	11.5 deg.C	935 mbar	45 Percen
1790018775	11.5 deg.C	935 mbar	45 Percen
1790018475	12 deg.C	935 mbar	45 Percen
1790018175	12 deg.C	935 mbar	45 Percen
1790017875	12 deg.C	935 mbar	45 Percen
1790017575	12 deg.C	935 mbar	45 Percen
1790017275	12 deg.C	935 mbar	45 Percen
1790016975	12 deg.C	935 mbar	45 Percen
1790016675	12 deg.C	935 mbar	45 Percen
1790016375	12 deg.C	935 mbar	45 Percen
1790016075	12 deg.C	935 mbar	44 Percen
1790015775	12 deg.C	935 mbar	44 Percen
1790015475	12 deg.C	935 mbar	44 Percen
1790015175	12 deg.C	935 mbar	43 Percen
1790014875	12 deg.C	935 mbar	43 Percen
1790014575	12 deg.C	935 mbar	43 Percen
1790014275	12 deg.C	935 mbar	43 Percen
1790013975	12 deg.C	935 mbar	42 Percen
1790013675	12 deg.C	935 mbar	41 Percen
1790013375	12 deg.C	935 mbar	42 Percen

*Used Equation Coefficients:

Temp: 0, 0.5, -40

Pres: 0, 1, 850

Humi: 0, 0.5, 0

xxx: 0, 1, 0

yyy: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)