M0WJW-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object M0WJW-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1761548564	12.8 Volt	220 Pkt	90 Pcnt
1761548264	12.8 Volt	230 Pkt	91 Pcnt
1761547964	12.8 Volt	230 Pkt	91 Pcnt
1761547670	12.8 Volt	240 Pkt	91 Pcnt
1761547364	12.8 Volt	230 Pkt	91 Pcnt
1761547064	12.8 Volt	230 Pkt	92 Pcnt
1761546764	12.8 Volt	240 Pkt	92 Pcnt
1761546464	12.8 Volt	230 Pkt	91 Pcnt
1761546164	12.8 Volt	240 Pkt	92 Pcnt
1761545864	12.8 Volt	250 Pkt	94 Pcnt
1761545564	12.8 Volt	250 Pkt	94 Pcnt
1761545264	12.8 Volt	250 Pkt	95 Pcnt
1761544964	12.8 Volt	240 Pkt	94 Pcnt
1761544664	12.8 Volt	250 Pkt	95 Pcnt
1761544364	12.8 Volt	250 Pkt	95 Pcnt
1761544064	12.8 Volt	240 Pkt	95 Pcnt
1761543764	12.8 Volt	240 Pkt	95 Pcnt
1761543464	12.8 Volt	240 Pkt	95 Pcnt
1761543164	12.8 Volt	250 Pkt	94 Pcnt
1761542864	12.8 Volt	240 Pkt	95 Pcnt
1761542564	12.8 Volt	230 Pkt	94 Pcnt
1761542264	12.8 Volt	240 Pkt	94 Pcnt
1761541964	12.8 Volt	240 Pkt	92 Pcnt
1761541664	12.8 Volt	230 Pkt	91 Pcnt
1761541364	12.8 Volt	230 Pkt	92 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)