DB8NR-8 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB8NR-8. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Temp*	Humi*	Baro*
1780514562	25 deg C	39.2 %	1011.5 hPa
1780513657	25.3 deg C	38.5 %	1012.3 hPa
1780512760	25.5 deg C	38.1 %	1012.6 hPa
1780511855	25.7 deg C	37.5 %	1013.3 hPa
1780510958	25.8 deg C	37.3 %	1011.3 hPa
1780510061	26 deg C	36.6 %	1010.8 hPa
1780509166	26.3 deg C	36 %	1012.4 hPa
1780508261	26.6 deg C	35.9 %	1010.6 hPa
1780507363	26.8 deg C	36 %	1011.9 hPa
1780506463	27.1 deg C	35.5 %	1011.9 hPa
1780505564	27.3 deg C	35.2 %	1012 hPa
1780504659	27.6 deg C	34.5 %	1014.3 hPa
1780503760	28.2 deg C	34.6 %	1012.2 hPa
1780502857	28.9 deg C	35 %	1012 hPa
1780502128	29.5 deg C	38.3 %	1017.9 hPa
1780501054	29.4 deg C	38.7 %	1009.2 hPa
1780500149	29 deg C	39.5 %	1013.7 hPa
1780499247	28.4 deg C	40.1 %	1010.7 hPa
1780498350	27.8 deg C	39.8 %	1012.3 hPa
1780490063	30.9 deg C	36.8 %	1011.6 hPa
1780489163	30.4 deg C	37.9 %	1014.7 hPa
1780488262	30.2 deg C	38.4 %	1019.2 hPa
1780487359	29.8 deg C	39 %	1014.8 hPa
1780486459	29.5 deg C	40.5 %	1013.6 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)