This is the latest recevied telemetry packets stored in our database for station/object WX5II-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Vin*
Rx1h*
Dg1h*
Eff1h*
A5*
1784662339
13.43 Volt
240 Pkt
100 Pkt
71 Pcnt
0 Pcnt
1784661739
13.43 Volt
250 Pkt
100 Pkt
69 Pcnt
0 Pcnt
1784658440
13.43 Volt
350 Pkt
120 Pkt
68 Pcnt
0 Pcnt
1784658139
13.43 Volt
370 Pkt
130 Pkt
70 Pcnt
0 Pcnt
1784654540
13.43 Volt
600 Pkt
150 Pkt
68 Pcnt
0 Pcnt
1784654539
13.43 Volt
600 Pkt
150 Pkt
68 Pcnt
0 Pcnt
1784650939
13.43 Volt
750 Pkt
180 Pkt
68 Pcnt
0 Pcnt
1784650640
13.43 Volt
800 Pkt
190 Pkt
68 Pcnt
0 Pcnt
1784647339
13.43 Volt
1310 Pkt
220 Pkt
70 Pcnt
0 Pcnt
1784646740
13.43 Volt
1330 Pkt
230 Pkt
68 Pcnt
0 Pcnt
1784643739
13.43 Volt
1330 Pkt
250 Pkt
64 Pcnt
0 Pcnt
1784642840
13.43 Volt
1300 Pkt
240 Pkt
63 Pcnt
0 Pcnt
1784640139
13.43 Volt
1310 Pkt
250 Pkt
62 Pcnt
0 Pcnt
1784638940
13.43 Volt
1350 Pkt
250 Pkt
63 Pcnt
0 Pcnt
1784636539
13.43 Volt
1310 Pkt
240 Pkt
62 Pcnt
0 Pcnt
1784635040
13.43 Volt
1250 Pkt
240 Pkt
61 Pcnt
0 Pcnt
1784632939
13.43 Volt
1320 Pkt
230 Pkt
66 Pcnt
0 Pcnt
*Used Equation Coefficients:
Vin: 0, 0.075, 0
Rx1h: 0, 10, 0
Dg1h: 0, 10, 0
Eff1h: 0, 1, 0
A5: 0, 0, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)