BM6HIP-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM6HIP-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1781559709	48.1 C	5 p	24 p	227 p
1781558508	47.6 C	8 p	24 p	222 p
1781557309	47.4 C	11 p	19 p	215 p
1781556109	47.9 C	5 p	12 p	204 p
1781554909	48.7 C	3 p	12 p	199 p
1781553708	48.6 C	4 p	12 p	196 p
1781552509	48.8 C	5 p	13 p	192 p
1781551309	48.2 C	3 p	15 p	187 p
1781550108	47.9 C	5 p	16 p	184 p
1781548908	48.1 C	7 p	14 p	179 p
1781547709	47.9 C	4 p	13 p	172 p
1781546509	48 C	3 p	16 p	168 p
1781545308	47.7 C	6 p	16 p	165 p
1781544108	47.7 C	7 p	12 p	159 p
1781542909	48 C	3 p	7 p	152 p
1781541709	48.5 C	2 p	6 p	150 p
1781540508	48 C	2 p	6 p	152 p
1781539308	47.4 C	2 p	6 p	150 p
1781538109	48.2 C	2 p	6 p	149 p
1781536909	48 C	2 p	10 p	156 p
1781535709	47.6 C	2 p	13 p	156 p
1781534508	47.6 C	6 p	14 p	154 p
1781533309	47.6 C	5 p	13 p	148 p
1781532109	47.7 C	3 p	12 p	143 p
1781530909	48.1 C	5 p	12 p	140 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)