SV6DBG-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SV6DBG-7. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Celsius*	Rel_Hum*	Atm_Press*
1781628941	31.9 C	43.45 %	1022.13 hPa
1781628099	31.2 C	31.55 %	1028.88 hPa
1781626325	31.5 C	30.75 %	1030.75 hPa
1781625767	31.8 C	29.88 %	1024.88 hPa
1781614182	34.8 C	27.23 %	1033 hPa
1781613463	34 C	25.11 %	1030 hPa
1781612818	32.7 C	26.09 %	1026.5 hPa
1781608668	31.4 C	36.08 %	1025.5 hPa
1781599638	30.9 C	36.94 %	1026.5 hPa
1781590608	30.3 C	34.65 %	1026.5 hPa
1781581578	30.4 C	32.59 %	1025.38 hPa
1781572548	30.6 C	33.17 %	1025 hPa
1781563518	32 C	33.72 %	1024.5 hPa
1781554488	31.9 C	36.1 %	1022.75 hPa
1781552387	31.7 C	28.09 %	1023.75 hPa
1781547496	31.6 C	28.19 %	1023 hPa
1781545363	30.5 C	32.25 %	1025.75 hPa
1781544408	31.1 C	31.51 %	1024 hPa
1781543761	31.2 C	29.86 %	1023.88 hPa
1781543166	31.1 C	31.03 %	1025.25 hPa
1781540995	29 C	38.56 %	1024.88 hPa
1781540459	29.5 C	37.62 %	1026.13 hPa
1781539923	30.2 C	36.37 %	1021.88 hPa
1781539407	30.6 C	35.13 %	1024.25 hPa
1781538878	30.9 C	34.41 %	1024 hPa

*Used Equation Coefficients:

Celsius: 0, 0.1, -50

Rel_Hum: 0, 0.01, 0

Atm_Press: 0, 0.125, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)