W2JKT-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W2JKT-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Voltage*	Current*	SOC*	Energy*
1788574130	13.3 V	0 A	98.6 %	14973 Wh
1788573530	13.3 V	0 A	98.6 %	14973 Wh
1788572930	13.3 V	0 A	98.6 %	14973 Wh
1788572330	13.3 V	0 A	98.6 %	14973 Wh
1788571730	13.3 V	0 A	98.6 %	14973 Wh
1788571130	13.3 V	0 A	98.6 %	14973 Wh
1788570530	13.3 V	0 A	98.6 %	14973 Wh
1788569930	13.3 V	0 A	98.6 %	14973 Wh
1788569330	13.3 V	0 A	98.6 %	14973 Wh
1788568730	13.3 V	-4.6 A	98.6 %	14973 Wh
1788568130	13.3 V	0 A	98.6 %	14973 Wh
1788567539	13.3 V	-3.5 A	100 %	14973 Wh
1788567530	13.3 V	0 A	98.6 %	14973 Wh
1788566930	13.3 V	0 A	98.6 %	14973 Wh
1788566926	13.3 V	-4.6 A	100 %	14973 Wh
1788566330	13.3 V	0 A	98.6 %	14973 Wh
1788566315	13.3 V	0 A	100 %	14973 Wh
1788565730	13.3 V	0 A	98.6 %	14973 Wh
1788565706	13.3 V	0 A	100 %	14973 Wh
1788565130	13.3 V	0 A	98.6 %	14973 Wh
1788565092	13.3 V	0 A	100 %	14973 Wh
1788564530	13.3 V	0 A	98.6 %	14973 Wh
1788564478	13.3 V	0 A	100 %	14973 Wh
1788563930	13.3 V	0 A	98.6 %	14973 Wh
1788563883	13.3 V	0 A	100 %	14973 Wh

*Used Equation Coefficients:

Voltage: 0, 0.1, 0

Current: 0, 0.1, -300

SOC: 0, 0.1, 0

Energy: 0, 1, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)