YD1OCG-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YD1OCG-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPU_Temp*	CPU_Load*	CPU_Freq*	RAM_Free*	Drive_Temp*
1789940053	31 C	2 %	1864 MHz	54 %	30 C
1789939798	31 C	4 %	1596 MHz	54 %	31 C
1789939555	32 C	4 %	1852 MHz	54 %	31 C
1789939258	31 C	4 %	1906 MHz	54 %	30 C
1789939003	31 C	4 %	1997 MHz	54 %	29 C
1789938708	31 C	4 %	2099 MHz	53 %	31 C
1789938463	31 C	4 %	1998 MHz	54 %	31 C
1789938178	31 C	6 %	1949 MHz	54 %	29 C
1789937938	31 C	6 %	1981 MHz	54 %	29 C
1789937683	31 C	2 %	2012 MHz	54 %	31 C
1789937443	32 C	2 %	1975 MHz	54 %	30 C
1789937147	31 C	4 %	1848 MHz	54 %	31 C
1789936888	32 C	4 %	1996 MHz	54 %	30 C
1789936647	32 C	2 %	1996 MHz	54 %	30 C
1789936377	31 C	2 %	2000 MHz	54 %	31 C
1789936093	31 C	2 %	1937 MHz	54 %	30 C
1789935823	31 C	6 %	1941 MHz	54 %	29 C
1789935578	31 C	6 %	1796 MHz	54 %	31 C
1789935333	31 C	4 %	1955 MHz	54 %	30 C
1789935053	31 C	6 %	2066 MHz	54 %	29 C
1789934758	31 C	6 %	2001 MHz	54 %	29 C
1789934498	32 C	8 %	1796 MHz	54 %	31 C
1789934223	32 C	2 %	1996 MHz	54 %	31 C
1789933928	31 C	4 %	2110 MHz	54 %	29 C
1789933647	32 C	4 %	2045 MHz	54 %	30 C

*Used Equation Coefficients:

CPU_Temp: 0, 1, 0

CPU_Load: 0, 1, 0

CPU_Freq: 0, 1, 0

RAM_Free: 0, 1, 0

Drive_Temp: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)