HS5TQA-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS5TQA-4. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	VBAT*	IBAT*	SOLAR*
1788580940	14.09 V	-80 mA	23.59 V
1788579140	13.85 V	40 mA	23.59 V
1788577340	13.81 V	44 mA	23.59 V
1788575540	13.86 V	-419 mA	23.59 V
1788573740	13.48 V	-328 mA	23.59 V
1788571940	13.46 V	-304 mA	23.59 V
1788570140	13.37 V	-170 mA	23.59 V
1788568340	13.3 V	-103 mA	23.59 V
1788566540	13.25 V	-26 mA	23.59 V
1788564740	13.22 V	46 mA	23.59 V
1788562940	13.23 V	51 mA	23.59 V
1788561140	13.22 V	55 mA	23.59 V
1788559340	13.21 V	74 mA	23.59 V
1788557540	13.23 V	48 mA	23.59 V
1788555740	13.23 V	52 mA	23.59 V
1788553940	13.23 V	51 mA	23.59 V
1788552140	13.23 V	54 mA	23.59 V
1788550340	13.23 V	58 mA	23.59 V
1788548540	13.23 V	49 mA	23.59 V
1788546740	13.22 V	127 mA	23.59 V
1788544940	13.23 V	55 mA	23.59 V
1788543140	13.24 V	52 mA	23.59 V
1788541344	13.24 V	47 mA	23.59 V
1788539540	13.24 V	45 mA	23.59 V
1788537740	13.25 V	52 mA	23.59 V

*Used Equation Coefficients:

VBAT: 0, 0.01, 0

IBAT: 0, 1, -2000

SOLAR: 0, 0.01, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)