BM6HIP-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM6HIP-13. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1781690284	27.5 C	24 p	90 p	2378 p
1781689083	27.3 C	33 p	94 p	2399 p
1781687883	27.4 C	33 p	88 p	2423 p
1781686682	27.9 C	28 p	91 p	2419 p
1781685483	28 C	27 p	91 p	2421 p
1781684283	27.4 C	36 p	95 p	2421 p
1781683083	27.4 C	28 p	91 p	2409 p
1781681883	27.5 C	31 p	89 p	2413 p
1781680683	27.9 C	32 p	97 p	2416 p
1781679500	28 C	26 p	92 p	2426 p
1781678285	27.6 C	39 p	89 p	2436 p
1781677082	27.9 C	27 p	83 p	2444 p
1781675882	27.9 C	23 p	87 p	2445 p
1781674682	28.1 C	33 p	94 p	2450 p
1781673483	27.4 C	31 p	105 p	2452 p
1781672283	28.1 C	30 p	99 p	2441 p
1781671082	27.9 C	44 p	94 p	2431 p
1781669883	28 C	25 p	82 p	2451 p
1781668683	28 C	25 p	85 p	2461 p
1781667483	28.1 C	32 p	84 p	2496 p
1781666282	27.5 C	28 p	76 p	2504 p
1781665095	27.5 C	24 p	69 p	2511 p
1781663883	27.5 C	24 p	69 p	2526 p
1781662683	27.1 C	21 p	73 p	2564 p
1781661482	27.6 C	24 p	75 p	2560 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)