F4DVI Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F4DVI. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1780540101	13.95 Volt	50 Pkt	44 Pcnt
1780540100	13.95 Volt	50 Pkt	44 Pcnt
1780539801	13.95 Volt	50 Pkt	41 Pcnt
1780539800	13.95 Volt	50 Pkt	41 Pcnt
1780539501	13.95 Volt	50 Pkt	39 Pcnt
1780539500	13.95 Volt	50 Pkt	39 Pcnt
1780539201	13.95 Volt	50 Pkt	37 Pcnt
1780539200	13.95 Volt	50 Pkt	37 Pcnt
1780538901	13.95 Volt	50 Pkt	36 Pcnt
1780538900	13.95 Volt	50 Pkt	36 Pcnt
1780538601	13.95 Volt	40 Pkt	35 Pcnt
1780538600	13.95 Volt	40 Pkt	35 Pcnt
1780538301	13.95 Volt	40 Pkt	36 Pcnt
1780538300	13.95 Volt	40 Pkt	36 Pcnt
1780538001	13.95 Volt	40 Pkt	35 Pcnt
1780538000	13.95 Volt	40 Pkt	35 Pcnt
1780537701	13.95 Volt	50 Pkt	39 Pcnt
1780537700	13.95 Volt	50 Pkt	39 Pcnt
1780537401	13.95 Volt	50 Pkt	40 Pcnt
1780537400	13.95 Volt	50 Pkt	40 Pcnt
1780537101	13.95 Volt	50 Pkt	43 Pcnt
1780537100	13.95 Volt	50 Pkt	43 Pcnt
1780536801	13.95 Volt	50 Pkt	43 Pcnt
1780536800	13.95 Volt	50 Pkt	43 Pcnt
1780536501	13.95 Volt	60 Pkt	44 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)